Description

Stainless Steel Threaded Unions

A stainless steel threaded union joins two threaded pipes while allowing the joint to be broken again without disturbing the rest of the line. Its three-piece construction — a male sub-end, a female sub-end and a central ring nut — lets maintenance teams disconnect equipment simply by unscrewing the nut.

Forged in 304/316 to ASME B16.11 / MSS SP-83, our unions are supplied with a metal-to-metal, integral or gasketed seat and in NPT, BSPT and BSPP threads. Unions are essential at pumps, valves, meters, strainers and any equipment that requires periodic removal.

Manufacturing & Construction

Our threaded unions are produced by hot forging bar or billet, which aligns the grain flow with the shape of the fitting and eliminates the porosity associated with castings. The forgings are then solution-annealed, machined to the ASME B16.11 body dimensions and thread-cut to the required NPT, BSPT or BSPP form. Every piece is finally pickled and passivated to restore the passive chromium-oxide layer that gives stainless steel its corrosion resistance.

Material Grades & Chemical Composition

The fittings are supplied as standard in austenitic grades 304, 304L, 316 and 316L, with higher alloys available on request. The low-carbon (L) grades are preferred where the fitting will be welded, as they resist sensitisation and intergranular corrosion in the heat-affected zone. Typical chemical composition (per ASTM A182) is shown below.

Dimensions & Standards

Dimensions, wall thickness and thread lengths conform to ASME B16.11 (forged fittings), with BS 3799 and MSS SP-83 also referenced. The standard size range is 1/8″ to 4″ nominal bore. Body dimensions increase with pressure class, so a Class 6000 fitting has a heavier wall than a Class 3000 fitting of the same size. Full centre-to-end and thread-engagement figures are available on our dimensional datasheet.

Pressure Class & Temperature Ratings

Threaded fittings to ASME B16.11 are rated by pressure class. Each class is derived from the strength of a matching schedule of pipe, and the allowable working pressure reduces as temperature rises. This product is available in Class 2000 and 3000.

Because austenitic stainless retains useful strength at elevated temperature and remains tough at cryogenic temperature, these fittings serve across a very wide temperature band; the exact allowable pressure at your design temperature should be taken from the ASME B16.11 rating tables for the selected class and grade.

Threading & Sealing

We supply three thread forms so the fitting can be matched to any piping standard. Tapered threads (NPT, BSPT) seal on the thread flanks with PTFE tape or sealant; parallel threads (BSPP) require a bonded washer, O-ring or gasket to seal.

Testing, Inspection & Certification

Each heat is verified for chemical composition and mechanical properties (tensile, yield, elongation and hardness). Positive material identification (PMI) confirms the grade, and hydrostatic or pneumatic testing, dye-penetrant examination and intergranular corrosion (IGC) testing to ASTM A262 are carried out where the order requires. Fittings are marked with the heat number, size, grade, class and brand, and are supplied with an EN 10204 3.1 mill test certificate with full traceability.

Installation Guidelines

To make a reliable, leak-free joint and to join two pipes with a make-and-break connection for maintenance correctly:

• Screw each sub-end onto its pipe using PTFE tape or sealant on the pipe threads.
• Bring the two sub-ends together, ensuring the seating faces are clean and undamaged.
• Hand-start the ring nut squarely, then tighten to draw the seats together — do not use sealant on the union seat itself.
• To service the line, simply unscrew the ring nut; the pipes remain in place.

Applications & Industries

Stainless steel threaded unions are used across oil & gas, petrochemical and refining, chemical and fertiliser plants, power generation, pharmaceuticals, food and dairy, water treatment, shipbuilding and general engineering — anywhere a compact, corrosion-resistant, high-pressure screwed connection is needed.

Specifications at a Glance

Frequently Asked Questions

Q1. Why use a union instead of a coupling?

A union allows the joint to be disconnected for maintenance by unscrewing a single nut, whereas a coupling can only be removed by unscrewing one of the connected pipes. Unions are placed wherever equipment must be isolated or removed periodically.

Q2. What seat types are available on your unions?

Unions are offered with metal-to-metal (conical) seats, integral seats and gasketed/PTFE-seat designs. Metal seats suit high temperatures and clean service; gasketed seats give an easier reseal on lower-pressure duties.

Q3. Should sealant be applied to the union seat?

No. Thread sealant or PTFE tape is applied only to the pipe threads on the sub-ends. The union seat is a machined sealing face and must be kept clean and undamaged; sealant on the seat can prevent a proper seal.

Q4. What pressure classes are unions available in?

Threaded unions are typically supplied in Class 2000 and Class 3000. For higher pressures, alternative high-pressure union designs or flanged connections are used.

Q5. Can a union be repeatedly disconnected and remade?

Yes, that is its purpose. Provided the seating faces are kept clean and are not scored or over-torqued, a union will reseal reliably through many make-and-break cycles.

Q6. Where should unions be located in a system?

Place unions close to pumps, control valves, meters, strainers and instruments so these items can be removed without cutting or unscrewing long pipe runs.

Q7. What material grades are your threaded unions available in?

They are manufactured in austenitic stainless steel grades ASTM A182 F304, F304L, F316 and F316L as standard, with F321, F310, 904L and duplex/super-duplex (F51, F53, F55) available on request. Grade selection depends on the operating temperature, media and corrosion environment.

Q8. What is the difference between 304 and 316 for threaded fittings?

Grade 316 contains 2–3% molybdenum, which gives significantly better resistance to chlorides, pitting and crevice corrosion, making it the preferred choice for marine, coastal and aggressive chemical service. Grade 304 is more economical and well suited to fresh water, steam, food and general industrial use.

Q9. What does the pressure Class (2000/3000/6000) mean?

The class is a pressure–strength rating defined by ASME B16.11. Class 2000 threaded fittings are rated on the basis of Schedule 80/XS pipe, Class 3000 on Schedule 160 and Class 6000 on Schedule XXS. A higher class means a heavier body and a higher allowable working pressure at a given temperature.

Q10. Which thread standards do you supply — NPT, BSPT or BSPP?

We supply NPT (ANSI/ASME B1.20.1, tapered), BSPT / R (BS 21 / ISO 7-1, tapered) and BSPP / G (BS 2779 / ISO 228, parallel). Tapered threads seal on the thread flanks; parallel threads require a bonded seal, washer or O-ring. Always match the fitting thread to the mating component.

Q11. What size range is available?

Standard sizes run from 1/8″ up to 4″ nominal bore. Intermediate and reducing combinations are available, and larger or special sizes can be produced to order.

Q12. Are the fittings forged or cast?

Our threaded fittings are hot forged and then machined and threaded. Forging produces a dense, void-free grain structure with superior mechanical strength and pressure integrity compared with cast fittings.

Q13. What test certificates are provided?

Every consignment is supplied with an EN 10204 3.1 mill test certificate covering chemical composition and mechanical properties, with heat-number traceability. 3.2 certification, PMI (positive material identification), hydrostatic/pneumatic test, dye-penetrant and IGC (intergranular corrosion) reports can be provided on request.

Q14. How should the threaded joints be sealed?

Tapered threads are normally sealed with PTFE tape or a suitable thread sealant applied to the male thread, then made up hand-tight plus the recommended number of turns with a wrench. Do not over-tighten, which can gall the stainless threads or split the fitting.

Q15. Do stainless steel threads gall, and how is it prevented?

Austenitic stainless can gall (cold-weld) if threads are made up dry and fast. Galling is prevented by using PTFE tape or an anti-seize/thread sealant, assembling slowly, and avoiding excessive torque. Using dissimilar grades on the two halves also reduces the tendency.

Q16. Can you supply custom sizes, grades or private marking?

Yes. In addition to the standard range we manufacture to customer drawings and specifications, including special sizes, higher classes, alternative grades and customer-specified heat/marking and packaging.

Request a Quotation

Stainless Steel Fittings India manufactures, stocks and exports the complete range of stainless steel threaded fittings in grades 304, 304L, 316 and 316L, in NPT, BSPT and BSPP threads and Classes 2000, 3000 and 6000. Every order is supplied with EN 10204 3.1 mill test certificates and full traceability, with custom sizes, grades and thread forms available.

Get pricing, stock availability and datasheets for your project: Contact our sales team »